Engineering Materials and Metallurgy for ANNA University (IV-Mech-2008 Course)
2 Angebote vergleichen
Bester Preis: € 8,53 (vom 08.05.2020)1
Engineering Materials and Metallurgy for ANNA University (IV-Mech-2008 Course) (2008)
~EN PB NW FEISBN: 9789350380499 bzw. 9350380498, vermutlich in Englisch, Technical Publications, Taschenbuch, neu, Erstausgabe.
Lieferung aus: Indien, Versandkosten nach: CHE.
Von Händler/Antiquariat, Sanctum Books.
Technical Publications. First edition. Softcover. New. Review (Not for Exam): Crystal structure - BCC, FCC and HCP structure - Unit cell - Crystallographic planes and directions, Miller indices - Crystal imperfections, Point, Line, Planar and volume defects - Grain size, ASTM grain size number. Unit I - Constitution of Alloys and Phase Diagrams Constitution of alloys - Solid solutions, Substitutional and Interstitial - Phase diagrams, Isomorphous, Eutectoid, Eutectic, Peritectic, and peritectroid reactions, Iron - Iron carbide equilibrium diagram. Classification of steel and cast iron, Microstructure, Properties and applications. Unit II - Heat Treatment Definition - Full annealing, Stress relief, Recrystallisation and spheroidizing -Normalising, Hardening and tempering of steel. Isothermal transformation diagrams - Cooling curves superimposed on I.T. diagram, CCR - Hardenability, Jominy end quench test - ¬Austempering, Martempering - Case hardening - Carburising, Nitriding, Cyaniding, Carbonitriding, Flame and induction hardening. Unit III - Mechanical Properties and Testing Mechanism of plastic deformation, Slip and twinning - Types of fracture - Testing of materials under tension, Compression and shear loads - Hardness tests (Brinell, Vickers and Rockwell), Impact test - Izod and Charpy, Fatigue and creep tests, Fracture toughness tests. Unit IV - Ferrous and Non - Ferrous Metals Effect of alloying elements on steel (Mn, Si, Cr, Mo, V, Ti & W) - Stainless and tool steels - HSLA - Maraging steels - Cast irons - Grey, White malleable, Spheroidal - Graphite, Alloy cast irons, Copper and Copper alloys - Brass, Bronze and Cupronickel - Aluminium and AI-Cu alloy - Precipitation hardening- Bearing alloys. Unit V - Non-Metallic Materials Polymers - Types of polymer, Commodity and engineering polymers - Properties and applications of PE, PP, PS, PVC, PMMA, PET, PC, PA, ABS, PI, PAl, PPO, PPS, PEEK, PTFE polymers - Urea and phenol formaldehydes - Engineering ceramics -Introduction to fibre reinforced plastics. Printed Pages: 510.
Von Händler/Antiquariat, Sanctum Books.
Technical Publications. First edition. Softcover. New. Review (Not for Exam): Crystal structure - BCC, FCC and HCP structure - Unit cell - Crystallographic planes and directions, Miller indices - Crystal imperfections, Point, Line, Planar and volume defects - Grain size, ASTM grain size number. Unit I - Constitution of Alloys and Phase Diagrams Constitution of alloys - Solid solutions, Substitutional and Interstitial - Phase diagrams, Isomorphous, Eutectoid, Eutectic, Peritectic, and peritectroid reactions, Iron - Iron carbide equilibrium diagram. Classification of steel and cast iron, Microstructure, Properties and applications. Unit II - Heat Treatment Definition - Full annealing, Stress relief, Recrystallisation and spheroidizing -Normalising, Hardening and tempering of steel. Isothermal transformation diagrams - Cooling curves superimposed on I.T. diagram, CCR - Hardenability, Jominy end quench test - ¬Austempering, Martempering - Case hardening - Carburising, Nitriding, Cyaniding, Carbonitriding, Flame and induction hardening. Unit III - Mechanical Properties and Testing Mechanism of plastic deformation, Slip and twinning - Types of fracture - Testing of materials under tension, Compression and shear loads - Hardness tests (Brinell, Vickers and Rockwell), Impact test - Izod and Charpy, Fatigue and creep tests, Fracture toughness tests. Unit IV - Ferrous and Non - Ferrous Metals Effect of alloying elements on steel (Mn, Si, Cr, Mo, V, Ti & W) - Stainless and tool steels - HSLA - Maraging steels - Cast irons - Grey, White malleable, Spheroidal - Graphite, Alloy cast irons, Copper and Copper alloys - Brass, Bronze and Cupronickel - Aluminium and AI-Cu alloy - Precipitation hardening- Bearing alloys. Unit V - Non-Metallic Materials Polymers - Types of polymer, Commodity and engineering polymers - Properties and applications of PE, PP, PS, PVC, PMMA, PET, PC, PA, ABS, PI, PAl, PPO, PPS, PEEK, PTFE polymers - Urea and phenol formaldehydes - Engineering ceramics -Introduction to fibre reinforced plastics. Printed Pages: 510.
2
Engineering Materials and Metallurgy for ANNA University (IV-Mech-2008 Course) (2008)
~EN PB NW FEISBN: 9789350380499 bzw. 9350380498, vermutlich in Englisch, Technical Publications, Taschenbuch, neu, Erstausgabe.
Lieferung aus: Indien, Versandkosten nach: CHE.
Von Händler/Antiquariat, BookVistas.
Technical Publications. First edition. Softcover. New. Review (Not for Exam): Crystal structure - BCC, FCC and HCP structure - Unit cell - Crystallographic planes and directions, Miller indices - Crystal imperfections, Point, Line, Planar and volume defects - Grain size, ASTM grain size number. Unit I - Constitution of Alloys and Phase Diagrams Constitution of alloys - Solid solutions, Substitutional and Interstitial - Phase diagrams, Isomorphous, Eutectoid, Eutectic, Peritectic, and peritectroid reactions, Iron - Iron carbide equilibrium diagram. Classification of steel and cast iron, Microstructure, Properties and applications. Unit II - Heat Treatment Definition - Full annealing, Stress relief, Recrystallisation and spheroidizing -Normalising, Hardening and tempering of steel. Isothermal transformation diagrams - Cooling curves superimposed on I.T. diagram, CCR - Hardenability, Jominy end quench test - ¬Austempering, Martempering - Case hardening - Carburising, Nitriding, Cyaniding, Carbonitriding, Flame and induction hardening. Unit III - Mechanical Properties and Testing Mechanism of plastic deformation, Slip and twinning - Types of fracture - Testing of materials under tension, Compression and shear loads - Hardness tests (Brinell, Vickers and Rockwell), Impact test - Izod and Charpy, Fatigue and creep tests, Fracture toughness tests. Unit IV - Ferrous and Non - Ferrous Metals Effect of alloying elements on steel (Mn, Si, Cr, Mo, V, Ti & W) - Stainless and tool steels - HSLA - Maraging steels - Cast irons - Grey, White malleable, Spheroidal - Graphite, Alloy cast irons, Copper and Copper alloys - Brass, Bronze and Cupronickel - Aluminium and AI-Cu alloy - Precipitation hardening- Bearing alloys. Unit V - Non-Metallic Materials Polymers - Types of polymer, Commodity and engineering polymers - Properties and applications of PE, PP, PS, PVC, PMMA, PET, PC, PA, ABS, PI, PAl, PPO, PPS, PEEK, PTFE polymers - Urea and phenol formaldehydes - Engineering ceramics -Introduction to fibre reinforced plastics. Printed Pages: 510.
Von Händler/Antiquariat, BookVistas.
Technical Publications. First edition. Softcover. New. Review (Not for Exam): Crystal structure - BCC, FCC and HCP structure - Unit cell - Crystallographic planes and directions, Miller indices - Crystal imperfections, Point, Line, Planar and volume defects - Grain size, ASTM grain size number. Unit I - Constitution of Alloys and Phase Diagrams Constitution of alloys - Solid solutions, Substitutional and Interstitial - Phase diagrams, Isomorphous, Eutectoid, Eutectic, Peritectic, and peritectroid reactions, Iron - Iron carbide equilibrium diagram. Classification of steel and cast iron, Microstructure, Properties and applications. Unit II - Heat Treatment Definition - Full annealing, Stress relief, Recrystallisation and spheroidizing -Normalising, Hardening and tempering of steel. Isothermal transformation diagrams - Cooling curves superimposed on I.T. diagram, CCR - Hardenability, Jominy end quench test - ¬Austempering, Martempering - Case hardening - Carburising, Nitriding, Cyaniding, Carbonitriding, Flame and induction hardening. Unit III - Mechanical Properties and Testing Mechanism of plastic deformation, Slip and twinning - Types of fracture - Testing of materials under tension, Compression and shear loads - Hardness tests (Brinell, Vickers and Rockwell), Impact test - Izod and Charpy, Fatigue and creep tests, Fracture toughness tests. Unit IV - Ferrous and Non - Ferrous Metals Effect of alloying elements on steel (Mn, Si, Cr, Mo, V, Ti & W) - Stainless and tool steels - HSLA - Maraging steels - Cast irons - Grey, White malleable, Spheroidal - Graphite, Alloy cast irons, Copper and Copper alloys - Brass, Bronze and Cupronickel - Aluminium and AI-Cu alloy - Precipitation hardening- Bearing alloys. Unit V - Non-Metallic Materials Polymers - Types of polymer, Commodity and engineering polymers - Properties and applications of PE, PP, PS, PVC, PMMA, PET, PC, PA, ABS, PI, PAl, PPO, PPS, PEEK, PTFE polymers - Urea and phenol formaldehydes - Engineering ceramics -Introduction to fibre reinforced plastics. Printed Pages: 510.
Lade…